News center
Our products are easy to use, convenient and safe


Jun 06, 2023

Fiber laser welding continues to grow as a preferred process with improvements in weld quality, reliability and performance. Many fiber laser welding applications are autogenous where the weld is formed entirely by melting parts of the base metal and no additional filler wire or powder is used.

Laser beam welding applications are almost always autogenous for a wide variety of materials. However, certain challenging materials and difficult applications require the use of filler material in the welding process. In doing so, big improvements in the weld process are possible.

Application improvements include:

Laser welding with filler material can be done with powder or wire ( see Figure 1). However, the majority of industrial laser welding applications use wire. This article focuses on fiber laser welding with wire. It should be noted that one of the reasons wire is preferred is its lower cost. Usually, powder feedstock is more expensive than wire feedstock for most materials. For example, a typical cost of 0.9 mm diameter Inconel 625 wire is $26/lb compared to $48/lb for powder of the same material. For that reason, powder is primarily used in additive manufacturing applications and not for welding.

As a multiparameter process, laser welding with filler wire is affected by several conditions which determine quality, process speed and cost.

Welding/filler wire speed: The wire feed rate for a given air gap and plate thickness is an important parameter and is dependent on welding speed, the cross section area of the gap between the joint face and cross sectional area of the filler wire. The relationship is expressed as follows:

Wire feed rate (m/min) = welding speed (m/min)*cross section area of gap (mm2)/ cross section area of wire (mm2)

The use of filler wire generally results in a 10 to 20 percent decrease in welding speed, for a given laser power, to compensate for the laser energy that has to be used to melt the wire. Note that the lower speed tradeoff is offset by the increased benefits of utilizing filler wire. But it is important to use the correct filler wire rate. If the filler wire rate is too low the amount of heat generated from the laser beam will affect the wire and the material being welded by being able to melt a larger section on the wire end. This may result in breaking a liquid metal bridge formed during the process and the formation of a drop at the end of the wire and momentary disturbance of the process stability.

A too-high filler wire rate can cause the energy supplied to the welding area to be insufficient for stable and permanent wire melting. The volume of liquid metal at the end of the wire and in the liquid metal bridge increases thus flooding the air gap. Additionally, non-melted wire enters the back area of the pool, pushing out the liquid metal, which by solidifying, forms characteristic humps of the weld surface and porosity at the root of the weld. A correct weld speed will ensure correct penetration depth, weld width and top bead height.

Laser beam-filler wire interaction: An exposed length of wire that is too short prevents the wire from being melted at the initial area of the bead and the laser beam directly affected the material to be melted. In turn, an exposed length of wire that is too long causes the extended wire end to be pressed against the plate surface. At the initial stage, the laser beam melts the wire through, dividing it into two parts. As a result, the spot at which the process started was covered with a wire end that is welded to the surface and difficult to remove. In an extreme case, the welded-on wire end could cause a collision with the gas shielding nozzle, disturbing or even eliminating the gas shielding. The control features of the LASERDYNE 795 with BeamDirector ensures correct laser beam, filler wire interaction.

The LASERDYNE 795 with BeamDirector is ideally designed for fiber laser welding will filer wire. The System S94P controller ensures crash protection while providing optimal gas shielding and control of laser parameters.

Wire feed delivery angle: Angles between 30 and 60 degrees from the vertical can be used and 45 degrees tends to be the norm as it simplifies setting the required wire intersection position with the laser beam centerline. Angles greater than 60 degrees makes the latter difficultand angles less than 30 degrees cause the wire to intersect a large area of the laser beam, causing melting and vaporization of the wire without incorporating it into the weld pool.

Focused spot size: The spot size should be close to the filler wire diameter. If the laser spot size is too small compared to the wire diameter, that can lead to welds with porosity because the filler wire has not melted properly.

Prima Power Laserdyne has carried out detailed studies of laser welding with filler wire with its LASERDYNE 795 with BeamDirector system. Both weld and filler wire parameters were developed and optimized to produce good quality welds without cracking or porosity with correct weld geometry. Figure 2 highlights welds made with filler wire to eliminate cracks and porosity (2a & 2b) and to improve the weld geometry (2c & 2d).

(2a upper left) 4mm thick 6065 aluminum alloy (Al-Mg-Si-Cu) welded with 0.8mm diameter 6065 wire; double pass Tee joint. This alloy is well suited for many applications in the aerospace industry, however is prone to solidification cracking without the filler material.

(2b upper right) 2mm thick 6061 aluminum alloy (Al-Mg-Si) welded with 1.0mm diameter 4047 wire; butt joint with 0.2mm gap. This alloy is mainly used for automotive applications.. This alloy is also prone to solidification cracking without the filler wire.

(2c lower left)3.2 thick Inconel 625 nickel based superalloy welded with 1.2mm diameter 625 wire; butt joint. This high temperature alloy is mainly used for aerospace applications. This alloy is not prone to cracking but for this application wire was used to compensate for the poor fit-up, mismatch and improve the weld geometry.

(2d lower right) 1mm thick Inconel 718 nickel based superalloy welded with 1.2mm diameter Inconel 625 wire; butt joint. Inconel 718 is being extensively used for high-temperature applications. Filler wire was used to meet the weld geometry i.e. top bead and bottom bead seam width and waist (center of the weld).

Extensive testing, as described above, has shown that fiber laser welding using filler wire has been proven effective in producing high quality, robust welds with improved fit-up, reduced weld cracking and better weld profile. The wide range of applications include aerospace, automotive and many industrial fabricating applications. Control of the laser weld metallurgy and dimensions are possible with the enhanced control of fiber laser welding process parameters that are made to happen using LASERDYNE’S 795 with BeamDirector fiber laser welding systems.

For more information about LASERDYNE products and services of Prima Power Laserdyne, call 763-433-3700, email: [email protected], or visit Prima Power Laserdyne is headquartered at 8600 109th Avenue North, #400, Champlin, Minnesota 55316.

Connect With Us

Mohammed Naeem Welding/filler wire speed Laser beam-filler wire interaction: Wire feed delivery angle Focused spot size: Figure 2 (2a upper left) aerospace industry (2b upper right) automotive applications. (2c lower left) aerospace applications (2d lower right) Sharpe Products and BLM Group David Giebenhain Brad Marley